Micanan PRO-H Instruction Manual Page 1

INSTALLATION AND INSTRUCTION MANUAL MODELS: PRO-J, PRO-H AUG, 2010

8 9. Carefully re-align sprockets, if necessary and secure keyway and set screws. 10. (For PRO-H models): Install hand chain by wrapping it throug

9 THERE ARE 3 POSSIBLE ELECTRICAL CONTROL CONFIGURATIONS FOR THIS OPERATOR: A) Standard relay logic controls (not UL325 2010 compliant, not

10 SECTION A: PRO-J, PRO-H Standard relay logic controls (not UL325 2010 compliant, not available in US) POWER WIRING: Use 1-1/8” (2.85 cm)

11 1. Reversing Edge device (must be normally open contact): Note: If the door is controlled by any device or wired in such a manner that th

12 SECTION B: PRO-J(M), PRO-H(M) Relay logic controls with Interface Module (UL325 2010 compliant) Operator electrical connections and start-up in

13 Single phase operators: The operators leave the factory with correct motor and limit shaft direction according to standard door installations. H

14 6) Connect safety devices Failsafe feature: A monitored failsafe safety feature is built into the operator. The operator has provisions to conne

15 SECTION C: PRO-J(E), PRO-H(E) Full feature logic board Smart 10.0 (UL325 2010 compliant) Note: The operator is shipped from the factory in the

16 For 3-phase operators: If door moves in wrong direction, turn off incoming power and reverse any two of the three incoming power supply leads to

17 Secondary non-monitored safety device(s): A standard 2-wire safety edge, non-monitored photo beams or any other non-monitored reversing devices w

18 C2 (Momentary open, constant pressure close) • Open Button: Momentary activation opens the door. When door is closing, momentary activation rever

19 • Timer to close: Closes the door from mid-stop or full open. Momentary activation of stop button will de-activate the timer. When door is closing

20 MID-STOP SETUP: Mid-stop feature can be used to open the door to a preset point prior to full open position. To Activate mid-stop: 1. Close th

21 PROGRAMMING THE ON-BOARD RADIO RECEIVER Warning: During programming, door operator will activate. Keep people and objects away from door. 1. C

22 DIPSWITCH SETUP Dip-switch ON OFF NOTE SEQ/COM Single button and radio in SEQ mode Single button and radio in COM mode Mid-stop timer Timer is

23 SECTION D: For all operator control types Adjustment of door travel is done by moving the limit cams on the threaded shaft. The position of

24 SECTION E: For Operators with Interface Modules or Logic boards Installation Safety Precautions WARNING: MICANAN MK00649 NEMA-1 infrared ph

25 3- Using the wing nuts, attach the receiver and transmitter of the photo system to the mounting brackets (with arrow pointing up). Note that th

26 3. Using the 8 phillips head screws, attach the receiver and the transmitter to the two mounting plates (Fig 2A). 4. Using the wing nuts, attach

27 1. Remove cotter pin tapped to pulley. 2. Rotate clutch nut counterclockwise (loosen) until there is insufficient tension to permit clutch t

28 - The PRO-J and PRO-H operators are equipped with an emergency disconnect device with interlocked power cut-out switch to manually operate d

29 - Inspect manual function of the door every 3-months. Make sure that door runs smoothly. If door does not manually open or clo

30

31 PRO-J PRO-JBCODE PART # DESCRIPTION (PRO-J/JB) C/W BRAKEQTY QTY** 1 MOTOR 1 1MM00150 2 FRAME HR MSI0162 1 1MM00152 3

32

33 PRO-H PRO-HBCODE PART # DESCRIPTION (PRO-H/HB) C/W BRAKEQTY QTY** 1 MOTOR 1 1MM00150 2 FRAME HR MSI0162 1 1MM00152 3 CONTROL BOX HR MSI0164 1 1MM

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

36

37

2 TABLE OF CONTENTS PAGE: VERIFICATION OF OPERATOR AND HARDWARE ___________________

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!

40

41

NOTES

NOTES

NOTES

NOTES

42 WARRANTY HEAD OFFICE 1380 St-Regis | Dorval, Quebec | H9P 2T5 | Canada TEL: (514) 822-1116 Toll Free: 1-877-888-1116

3 IMPORTANT FOR ANY QUESTIONS CONCERNING THE SAFETY OR OPERATION OF THIS OPERATOR PLEASE CONTACT MICANAN SYSTEMS AT 1-877-888-1116 SAVE THESE INST

4 PRO-J and PRO-H heavy-duty jackshaft operators are designed for commercial and industrial high lift, vertical lift, rolling doors and roll

5 - READ AND FOLLOW ALL INSTRUCTIONS - Never allow children to operate or play with door controls. Keep the remote control (where p

6 Note: - Installation of operator must be done by a qualified installer. Door must be properly installed and working smoothly. Remov

7 3. As a general rule, the door operator should be installed below the drive shaft and as close to the door as possible. The ideal distance betw